INFORMATION

Unlock the power of 10-Gigabit Ethernet with our high-performance 10GBASE-T Copper SFP+ Transceiver. This module provides a flexible and cost-effective solution for connecting SFP+ ports on switches, routers, and network interface cards to standard RJ45 Ethernet cables.

Designed for seamless integration, it supports data rates up to 10Gbps and is fully compliant with IEEE 802.3 standards for both 10GBASE-T and 1000BASE-T, ensuring backward compatibility with existing Gigabit Ethernet infrastructure. Achieve reliable connections up to 30 meters using Category 6A (or higher) cabling, making it ideal for top-of-rack switching and short-run data center links.

Product Features
Ø Up to 10Gbps bi-directional data links                     
Ø RJ45 Max 30m
Ø Fully metallic enclosure for low EMI
Ø Compact RJ-45 Connector assembly
Ø Hot-pluggable SFP footprint             
Ø Low power dissipation                 
Ø Extended case temperature: 0℃ to 70℃    
Ø RoHS compliant and Lead Free  
     
Applications
10 Gigabit Ethernet  
                                                    
Product Description
The BD-10GLC-T is Copper Small Form pluggable (SFP) transceiver, which is based on SFP multi-sourcing agreement (MSA). It is compatible with the 10GBASE-T and 1000BASE-T standards as specified in IEEE Std 802.3.The 1000BASE-T physical layer IC(PHY) can be accessed via I2C,allowing access to LIMITED PHY settings and features.
 
Regulatory Compliance
The transceivers are Class 1 Laser Products comply with FDA regulations. Meet Class 1 eye safety requirements of EN 60825 and the electrical safety requirements of EN 60950.
 
+3.3V Volt Electrical Power Interface
The BD-10GLC-T has an input voltage range of 3.3V +/-5%,The 4 V maximun voltage is not allowed for continuous operation.

Caution:Power consumption and surge current are higher than the specified values in the SFP MSATable 1.+3.3 Volt electrical power interface
 
Low-Speed Signals

Table 2. Low-speed signals, electronic characteristics
 
High-Speed Electrical Interface
ALL high-speed signals are AC-coupled internally
(1)High-speed Electrical Interface Transmission Line-SFP

Table 3. High-speed electrical interface,transmission line-SFP
 
(2)High-speed Electrical Interface,Host-SFP

 Table 4. High-speed electrical interface,host-SFP
General Specifications

Table 5. General specifications
Note:
1.Clock tolerance is +/- 50 ppm
2.By default,the CLBD-10GLC-T is a full duplex device in preferred master mode
3.Automatic crossover detection is enabled. External crossover cable is not required
4. Multi- BASE-T operation requires the host system to have an SGMII interface with no clocks, and the module PHY to be configured per Applications Note AN-2036.With a SERDES that does not support SGMII,the module will operate at single rate only.
Environmental Specifications
The BD-10GLC-T has an extended range from 0℃ to +70℃ case temperature as specified in Table.

Table 6. Environmental specifications
Pin Descriptions 

Table 7. SFP to host connector pin assignments and descriptionsNotes:
1. Circuit ground is connected to chassis ground.
2.PHY disabled on TDIS>2.0V or open,enabled on TDIS<0.8V.
3.Should be pulled up with 4.7k – 10k Ohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
 
Serial Communication Protocol
BD-10GLC-T supports the 2-wire serial communication protocol outlined in the SFP MSA.
The physical layer IC can also be accessed via the 2-wire serial bus at address Ach.